If a Samsung dryer tumbles but the load comes out cold, start with the checks Samsung publishes before you assume the heating element has failed. Samsung's "clothes are not dry" guide first asks you to confirm the cycle you selected, because some settings, including Eco Dry, run part of the cycle without heat. It then has you feel for warmth after a short run, and only continue into the power, gas and vent steps if the dryer doesn't heat at all.
Do those owner checks first. If a heating or vent-blockage code stays on, or the drum is still cold after the supply and vent are confirmed, dryer repair in Calgary is the usual next step.

Key Takeaways
- Samsung says some cycles, including Eco Dry, operate without heat at the start. Confirm the cycle is one that's supposed to heat.
- After 30 seconds, open the door and feel inside. If you feel any warmth, Samsung treats that as "not hot enough," not a no-heat fault, and points you to a different path.
- Electric models need a 240V outlet. The panel and motor can still run when the heater isn't getting enough voltage.
- On a gas dryer, confirm the gas connection is on and correctly installed. If you smell gas, leave the home right away without using light switches, phones or anything that could spark, then call ATCO at 1-800-511-3447 or 911 from outside.
- Samsung's vent blockage test can return results such as 0 or End (clear), or CLg, Cg, C80 or C90 when a clog is detected.
Confirm the cycle, then test for any heat
Samsung's guide starts with the cycle you selected. Eco Dry and certain other settings can run portions of the cycle, including the beginning, without heat. That can look like a failed heater when the dryer is doing what that program is designed to do. Check the cycle name on the panel, and use Samsung's cycle guide for your model if you're unsure.
Next, start a cycle that's supposed to heat, wait 30 seconds, open the door and feel inside the drum. Samsung draws a clear line here:
- If you feel any heat or warmth, the dryer is heating, just not enough to finish the load. That path belongs with a dryer that is not drying clothes, and with lint and vent work, not a dead heating circuit.
- Continue only if the dryer doesn't heat at all.
Power, gas and first-time installs
Samsung asks whether the dryer has ever heated in its current location. If it has never heated since it was installed, or since the installation was changed, the guide has you verify the supply before you dig into vents and codes.
| Dryer type | What Samsung has you check |
|---|---|
| Electric | A 240V outlet. If the outlet isn't supplying enough voltage, the panel and motor may still run, but the heater may not. Inspect the power-cord installation. |
| Gas | The gas line connection is installed properly and turned on. |
If you smell gas, don't keep troubleshooting. Leave the home right away without using light switches, phones or anything that could spark, then call ATCO at 1-800-511-3447 or 911 from outside. That number is for a gas emergency, not a routine "no heat" service call.
Lint, the exhaust vent and Samsung's blockage test
A packed lint filter or a restricted exhaust vent can keep a dryer from heating properly, and can also trip safety devices. Clean the lint filter before every load, and check the exhaust path. The walk-through on how to clean a dryer lint trap covers the filter. For the duct itself, use the guide on how to clean a dryer vent, or book dryer vent cleaning in Calgary if the run is long or hard to reach.
The NFPA dryer and washer safety tips, hosted by the U.S. Department of Energy, also stress keeping the lint filter and the exhaust clear. That's also a fire-safety step.
Many Samsung dryers include a vent blockage test. Samsung's guide lists these results:
| Result | What Samsung says it means |
|---|---|
| 0 or End | The duct isn't clogged. |
| CLg, Cg, C80 or C90 | A clog was detected. |
| Ct | The internal temperature is too low (below 32 F) or too high (over 104 F). Leave the dryer at room temperature for an hour and check again. |
| HC | An abnormal temperature was detected. Check the power cord, make sure the drum is empty, and test again. If the code returns, check the vent. If the vent is clean and the code remains, Samsung says to request service. |
| dc | The door is open. Shut it and run the test again. |
Samsung also says the exhaust vent must meet the dryer's requirements. A crushed, overly long or indoor-vented duct can fail that test even after you empty the lint screen.
Error codes that belong on the heating path
Samsung Canada's dryer error-code page groups the codes a Canadian machine may show, including voltage errors, door-related errors, temperature errors, heating errors and vent blockage test results. If the display shows a code, match it on that page before you order a part. Some codes mean you should stop and request service instead of continuing the owner checks.
For a generic "no heat" path that isn't Samsung-specific, see dryer not heating.
When to call for repair
Book a visit if the dryer still doesn't heat after you have confirmed the cycle, felt for warmth, checked the supply, cleaned the lint filter and cleared or tested the vent, or if a heating or HC code remains. We charge a $100 diagnostic, credited toward labour if you go ahead. Warranty is 3 months on parts and labour. Technicians reach Airdrie, Chestermere, Cochrane, Okotoks and Calgary, often arriving the same or next day.
Samsung dryer heating questions
Why is my Samsung dryer running but not getting hot? First confirm the cycle is supposed to heat. Samsung notes that Eco Dry can run part of the cycle without heat. Then feel for warmth after 30 seconds, and check power or gas, the lint filter and the vent.
Can a clogged vent stop a dryer from heating? Yes. Samsung's vent blockage test is built around that, and the NFPA safety tips treat a clear lint filter and exhaust as essential.
My electric dryer lights up but the drum stays cold. What should I check? Samsung says electric dryers need 240V. The controls can work on a weaker supply while the heater doesn't. If the dryer has never heated since it was installed in that location, inspect the power-cord installation and the outlet.
What should I do if I smell gas? Leave the home right away without using light switches, phones or anything that could spark, then call ATCO at 1-800-511-3447 or 911 from outside. Don't keep running the dryer.
To book a visit, use the online form or call 587-816-2400.
In-body photo: Dryer Lint Close by Chalome, CC BY-SA 3.0. Used at native size.