If your dishwasher isn't emptying when the cycle ends, begin with the owner checks the manufacturers publish: the filter, the drain hose, the sink or garbage disposal, and the air gap when one is fitted. GE Appliances treats a leftover puddle as a sign of a blockage, detergent suds, or a hose that wasn't set up correctly. Their page also describes a modest amount of clean leftover water as acceptable on certain models.
You'll want to try the steps in this guide first, without sliding the cabinet out, unless a hose check needs a little more room. If the tub stays wet after that, or a brand code remains, dishwasher repair in Calgary is the usual next step.

Key Takeaways
- On GE models with an Ultra Fine filter, leftover water should stay in the sump, not cover the tub floor.
- Bosch, Whirlpool, Samsung and Frigidaire all start with the filter, the hose, and the sink or disposal.
- After a new garbage disposal is installed, check that the knockout plug was removed. GE, Bosch, Whirlpool, Frigidaire and Samsung Canada all flag this.
- GE says not to use drain cleaner in the dishwasher.
- Bosch E24 and E25, and Whirlpool F9 E1, still begin with those same owner checks.
How to tell a drain problem from leftover water
How much leftover water is acceptable is spelled out in the GE Appliances support article. The allowance depends on the filter your model uses, as in the table below.
| Filter setup (GE) | What GE accepts |
|---|---|
| No Ultra Fine filter | 1 to 2 cups of clean water on the tub floor |
| Ultra Fine filter fitted | Water stays in the sump only |
You likely have a real drain problem if you notice:
- Water covering the tub floor after a finished cycle.
- A Bosch code such as E24 or E25, or a Whirlpool F9 E1 long-drain code.
- The cycle stopping early, or gurgling or humming that doesn't clear.
- The kitchen sink backing up when the dishwasher tries to drain.
Puddles beside the cabinet belong in the leaking-water article. Use the guide on a dishwasher leaking water.
Checks to try before you call, in order
These are the owner steps the brand pages share. Do them with the cycle finished and the machine cool. Frigidaire also reminds you to make sure the cycle is complete, not paused.
- Confirm how much water is left in the tub.
- Remove and clean the filter, and check the sump.
- Check the drain hose for kinks, pinches or a clog.
- Clear the sink or disposal, and check the knockout plug.
- Clean the air gap, or confirm the high loop.
- Look for suds from the wrong soap.
Step 1: Confirm how much water is left in the tub
Wait until the cycle has actually finished, then open the door and inspect the tub floor. Match what you see against the GE leftover-water rule in the section above. Keep going if the water is dirty, full of food, or spread across the tub.
Step 2: Remove and clean the filter, and check the sump
Bosch says the most common reason a dishwasher stops draining is food debris clogged in the filter or the water pump. Take the filter out, following your manual, and wash it with soap and a soft brush under running water. Before you put the filter back, Bosch tells you to remove the pump cover, check the pump, and sponge out debris and standing water. Use caution: some debris can be sharp.
Whirlpool's F9 E1 page also starts with removing the filter and cleaning it thoroughly under running water. Frigidaire tells you to check that the glass trap or filter is maintained, installed properly, and free of clogs. GE adds a check for paper or a large object covering the sump at the rear of the tub, and for large food such as noodles, lettuce or bones. For a fuller clean of the tub and racks, see our dishwasher deep-clean guide.
Step 3: Check the drain hose for kinks, pinches or a clog
Start at the cabinet end and follow the drain hose to the sink connection. Whirlpool's F9 E1 page lists kinks, pinches and clogs, and also asks you to confirm the hose is routed on the correct side of the frame. Samsung Canada's drain guide, written for dishwashers sold in Canada, warns that a new install can pin the hose against the cabinet, and that a twisted or damaged hose should be straightened or replaced. GE focuses on the joint under the sink, and says not to put an old, worn hose back into service.
Step 4: Clear the sink or disposal, and check the knockout plug
The dishwasher often shares a drain with the kitchen sink. If that shared path is blocked, the machine can't empty either. Samsung Canada starts this check at the sink: clear food from the disposal, then run the tap for 30 seconds. If the basin doesn't empty, they say the house drain is the likely cause and a plumber should take it. GE also says to run the disposer so the shared drain is clear, and don't put your hands into it.
After a disposal is fitted, confirm the dishwasher inlet is actually open. Many units leave that port blanked with a knockout, and the pump can't empty until it is removed. Bosch's E24 page flags it, as do GE, Whirlpool, Frigidaire and Samsung Canada. If the disposal itself won't run, use the guide to a garbage disposal that isn't working.
Step 5: Clean the air gap, or confirm the high loop
Check the counter next to the kitchen tap for a small chrome or plastic fitting, if your home uses one. That air gap is there to stop dirty water flowing back into the machine. GE has you lift the cap and clean it out. Whirlpool refers you to the fitting maker's own instructions. If you don't have that fitting, the drain hose needs to be looped high and clipped under the counter at the height in GE's install guide. Samsung Canada adds that local plumbing rules can require one of those two setups to prevent backflow.
Step 6: Look for suds from the wrong soap
GE says the wrong type of detergent, or too much of it, can cause over-sudsing that prevents the dishwasher from draining properly. On its F9 E1 page, Whirlpool says dishwashing detergent doesn't create suds, but dish soap does. If you open the door and see suds, bubbles or soap foam, Whirlpool says to turn the dishwasher off and let the suds die down, and to use only detergent made for automatic dishwashers. It also notes that suds can push water out of the machine and lead to leaking or poor wash performance.
Brand error codes that point to a drain problem
The owner checks stay the same when a code is on the display. The code only means the machine has already decided the water isn't leaving.
Bosch E24 and E25
Bosch says E24 means the dishwasher isn't draining properly because the drain filter is blocked. Possible causes it lists are a blocked drain hose, a filter that needs cleaning, and a new garbage disposal whose knockout plug is still in place. Its fix list also includes checking that the inlet hose isn't kinked or damaged, that the siphon connection is sealed, and that the pump cover under the filter isn't loose. Then reset the machine as the owner's manual describes.
Bosch's E25 article points to a blocked drain pump, or to a cover on that pump that is loose or gone. Their sequence is: take the filter out, check the cover, then (if you need to reach the pump) ease the cover off with a spoon until it clicks, lift it up and forward, and sponge out debris and standing water. Watch for sharp bits. Cut the power first. For a longer walk through the codes, see our Bosch dishwasher error codes guide.
Whirlpool F9 E1
Whirlpool lists F9 E1 as a long-drain error. After the filter, hose, disposal and air-gap checks, it says you can reset the control by cutting power for 30 seconds: unplug the machine, or switch the breaker off if it is hard-wired, then restore power.
When the checks aren't enough
The owner steps above clear a lot of drain problems. This table sums up where those steps end.
| What you see | DIY? | Why |
|---|---|---|
| A little clean water only in the filter well | Yes, often normal | GE says 1 to 2 cups can be normal without an Ultra Fine filter, and water in the sump can be normal with one |
| Water covering the tub after a cycle | Yes, start with the checks | The brand pages begin with the filter, hose, sink or disposal, air gap and soap |
| It started right after a new disposal was installed | Yes, check the knockout | GE, Bosch, Whirlpool, Frigidaire and Samsung Canada all flag an unremoved plug |
| The kitchen sink won't drain either | Plumber | Samsung Canada says that points to the house plumbing |
| E24, E25 or F9 E1 still on after the owner checks | Technician | The pump, hose routing or a failed part may need a visit |
| You suspect a frozen drain line | Plumber | Samsung Canada says to thaw the area if you can, and that warranty service doesn't cover frozen lines |
If the checks above leave standing water, or a code stays on, book dishwasher repair in Calgary. We charge a $100 diagnostic, credited toward labour if you go ahead. Warranty is 3 months on parts and labour. Technicians reach Airdrie, Chestermere, Cochrane, Okotoks and Calgary, often arriving the same or next day. For age-versus-repair questions, see how long dishwashers last.
Dishwasher drain questions
Can leftover water after a cycle still be acceptable? Yes, within the GE limits in the leftover-water table earlier in this article. Murky water or a flooded tub still needs the checks here.
Should I use drain cleaner in the dishwasher? No. GE says not to use drain cleaner in the dishwasher.
Why did the problem start right after a disposal was fitted? Many disposals ship with the dishwasher inlet still blanked off. Until that knockout is removed, the pump has no outlet. The drain articles from GE, Bosch, Whirlpool, Frigidaire and Samsung Canada all mention this.
What does a Bosch E24 or Whirlpool F9 E1 code mean? On Bosch's E24 page, the code means a blocked drain filter is stopping the water from leaving. Whirlpool's F9 E1 article calls that a long-drain condition. Do the owner checks first, then reset the way the brand describes. E25 is a separate Bosch code: a blocked drain pump, or a cover on that pump that is loose or gone.
To book a visit, use the online form or call 587-816-2400.
Featured image: Frigidaire Gallery Professional Series 20060513 by Pptudela, public domain. Cropped.